Concrete Column Volume Calculator
Calculate concrete volume for round and square columns. Enter dimensions and column count to get cubic yards for your concrete column project.
Sonotube Fill Calculator
Calculate concrete needed to fill Sonotubes. Enter tube diameter, height, and count to get volume in cubic yards or bags.
in
in
$
Per Tube Volume⧉
3.14 ft³
455 lbs of concrete per tube
Total Volume⧉
18.84 ft³
0.698 yd³ | 2,730 lbs total
60-lb Bags Needed⧉
42
Cost: $273.00 at $6.50/bag
80-lb Bags Needed⧉
32
Cost: $239.20 (80-lb bags)
Ready-Mix Cost⧉
$122.15
Bags cheaper — ready-mix better above ~1 yd³
Rebar Needed⧉
6 pieces
1 stick #4 rebar per tube (typical)
Cost Comparison: Bags vs Ready-Mix
60-lb Bags: $273.00
Ready-Mix: $122.15
Planning notes, formulas, and examples
About the Sonotube Fill Calculator
Sonotubes (round cardboard forming tubes) are the standard method for creating concrete piers for decks, porches, additions, and post-frame buildings. They provide a smooth, uniform cylindrical form that produces clean, consistent piers at an affordable cost.
This calculator determines the exact amount of concrete needed to fill your Sonotubes. Simply enter the tube diameter, height above the footing base, and the number of tubes. The calculator outputs volume per tube and total project volume in cubic feet, cubic yards, and pre-mixed bag equivalents.
Sonotubes come in diameters from 6 to 48 inches, with 8", 10", and 12" being most common for residential deck piers. The tube height depends on your frost depth and how far the pier extends above grade, typically 36–60 inches total.
When This Page Helps
Each Sonotube holds a specific volume of concrete, and miscalculating means either running short mid-pour or having expensive leftover ready-mix. For small pier projects, bags may be more economical; for larger projects, a ready-mix truck is more practical. This calculator helps you decide which approach makes sense.
How to Use the Inputs
- Enter the Sonotube diameter in inches (common sizes: 8", 10", 12").
- Enter the tube height in inches (from base of hole to top of pier).
- Enter the total number of tubes to fill.
- Review the per-tube volume and total volume.
- Decide between bags (small projects) or ready-mix truck (larger projects).
Formula used
Volume per tube = π × (diameter/2)² × height (in³)
Convert to ft³: ÷ 1728
Convert to yd³: ÷ 27
Bags (80-lb): total ft³ ÷ 0.6
Bags (60-lb): total ft³ ÷ 0.45Example Calculation
Result: 1.17 yd³ (53 bags of 80-lb)
Each 12" diameter tube, 48" tall: V = π × 6² × 48 = 5,429 in³ = 3.14 ft³. Six tubes: 18.85 ft³ = 0.70 yd³. Continuing, 18.85 / 0.6 = ~32 bags of 80-lb mix.
Tips & Best Practices
- Stake and brace Sonotubes securely before pouring — wet concrete exerts significant lateral pressure.
- Coat the inside of the tube with form release oil for easier stripping.
- Pour concrete in 12–18 inch lifts, consolidating each lift with a length of rebar worked up and down.
- For more than 10 tubes or 1+ cubic yards, consider ordering a ready-mix truck to save labor.
- Set anchor bolts or post brackets into the wet concrete while you can still adjust plumb alignment.
- In cold climates, extend piers at least 6 inches below the frost line.
Sonotube Size Selection
6–8" tubes support light structures like pergolas, small sheds, and mail box posts. 10–12" tubes are standard for residential decks and porches. 14–18" tubes handle heavy loads like additions and sunrooms. 24–48" tubes are used for commercial foundations and bridge piers.
Installation Best Practices
Dig the hole 2–4" wider than the tube diameter. Place 4–6 inches of compacted gravel at the bottom for drainage. Set the tube plumb, brace it securely, and backfill around the outside with soil to prevent shifting during the pour.
Bags vs. Ready-Mix Decision
As a rule of thumb, if total volume exceeds 1 cubic yard (about 45 bags of 80-lb mix), ordering a ready-mix truck saves significant time and labor. A mini-load from most ready-mix plants starts at 1 cubic yard with a small-load surcharge.
Sources & Methodology
Last updated:
Frequently Asked Questions
Most building codes require 8–12" diameter piers for residential decks, depending on the load each pier supports. 12" is the most common. Check your local code and have an engineer size piers for larger or multi-level decks.
The tube must extend below the local frost line. In northern climates, that's 36–48" or more. In southern states, 12–18" may suffice. The pier also typically extends 6" above grade to keep the structure off the ground.
While not always required by code for small piers, placing one or two lengths of #4 rebar improves tensile and lateral strength significantly. It's inexpensive insurance against cracking.
Yes, for small projects (under 1 cubic yard), hand-mixing bags is practical. An 80-lb bag makes 0.6 ft³, so a 12" tube 48" tall needs about 5–6 bags. For larger projects, a ready-mix truck is faster.
Use a circular saw, reciprocating saw, or hand saw to cut cardboard tubes. Mark the cut line all the way around using a tape measure and a level. A utility knife works for thin-wall tubes.
The portion below grade is typically left in place — it eventually degrades harmlessly. The portion above grade should be stripped (peeled off) within 1–7 days for best appearance.
More in this topic
Post Hole Concrete Calculator
Calculate concrete needed for fence post holes. Enter hole diameter, depth, post size, and count to get bags or cubic yards required.
Concrete Bag Calculator
Calculate how many bags of concrete you need. Enter your project volume to get 40-lb, 60-lb, and 80-lb bag counts with cost estimates.